MAKKI INTENSIVE LASH AND BROW TINT
FOR PROFESSIONAL USE ONLY
We recommend that you carry out a skin allergy test 24 hours before
the treatment. To do the test mix a tiny amount of the dye with one drop of the
developer, and then apply to the crook of the elbow or behind the ear. 24 hours
later, check the area for any signs of redness, rash or soreness, if you see any
of these signs, do not proceed with the treatment.
1) Preparing the Client:
2) Selecting the activator:
|Client must be sitting upright in a chair with the head slightly
tilted back. DO NOT APPLY IF THE HEAD OR THE BODY IS LAID BACK IN A RECLINED
For eyelashes, use only 2% Developer, do not use any developer with higher volume. For Eyebrows, use 3% or 6 %
developer depending on the shade desired, original colour of the eyebrows, hair condition, etc.
3) Preparing the tint:
Shake the developer well before use. Mix ¾ inch (2 cm) of Colour Cream with
2-4 drops of the Developer until the consistency becomes a creamy paste. (Ensure
that consistency is not runny or drippy.). Let the mix develop for 3 minutes
while the client is being prepared.
4) Preparing the area to be treated
Cleanse the area to be treated thoroughly ensuring that it is completely free
of makeup, oil and grease. Use
non-oily makeup remover
), then finish
cleansing by wiping the area with a cotton pad damped in lukewarm water. Dry and
Skin protection cream
() under the lower lid and around the
eyes and / or eyebrows (if eyebrows also to be tinted) . Place
() under the lower lid to prevent the tint from staining the skin.
Using a tinting brush or application stick, apply the mix to the lower lashes
first ensuring that the tint covers the hair from base to tip. Make sure that
corner lashes are also covered. Then apply the tint to upper lashes from base to
tip. Make sure that corner lashes are covered.
Apply the mix to the eyebrows using a tinting brush or application stick, ensure
that you cover all hairs of the eyebrows.
When tinting is completed, instruct the client to sit quietly and relax until
the end of the treatment.
6) Processing time:
this depends on the following factors: original hair colour, tint desired,
coarseness and condition of the clients hair, and room temperature.
Although the usual processing time is 10 minutes for lashes and 3 minutes for
brows, these times may produce results darker than expected. If you are working
with Middle Brown, Brown or Graphite, we recommend that you allow eyelashes to
develop for 3 minutes and the eyebrows to develop for one and half minutes. Then
cleanse them and check the colour. If the eyelashes and/or eyebrows are not dark
enough, re-apply and allow to them to process again until the desired colour is
achieved. A general rule is that the longer you leave it, the darker the colour
7) Completing and Finishing the treatment:
Use a cotton swab dampened in soap and water to remove any tint from the
skin. DO NOT USE TINT SPOT CLEANSER ON THE SKIN. DO NOT ALLOW THE CREAM OR
DEVELOPER TO REACH THE EYES, NOSTRILS, OR EARS. IF THIS HAPPENS, IMMEDIATELY
FLUSH WITH WARM WATER AND DRY THE AREA.
Gently Remove the eye protection pads. Then, with the client’s eye closed,
use a cotton ball soaked in warm water to remove product until no residues are
visible. Use tissues to capture any dripping or excess.
NOTE: The colour of the mixture is not the colour that the hair will be once
it is tinted. To get an idea of the final colour, leave a wooden applicator in
the mixture for the desired time.
Instruction videos are available at
the developer may look a bit thick due to changing room temperature, this
does not affect the product quality. Always store in cool place.
You get 1 Tube of 22ml
Intensive Eyelash and Eyebrow Tint including an application stick as in the
picture above. Developers and all other accessories are sold separate.